Cable and pipe locator Success AG-511N

New easy-to-use cable and pipe locator based on AP-014 receiver.

Features:

New simple receiver AP-014 with LED indication
Audio indication
Reasonable price
Locating accuracy: ±0,3 m

Request price

Request demo

Overview

Brief description:

Operating frequencies: 50(60)* / 100(120)* / 512 / 1024 / 8192 / 32768 Hz
Broad band: 0,05 to 8,20 kHz
Visual indication: LED scale (7 values)
Audio indication: headphones natural, filtered and synthesized signal. Built-in emitter - synthesized signal
Min and max method of cable tracing
Transmitter – 20W
Transmitter frequencies: Hz - 512 - «0.5» / 1024 - «1.0» / 8192 - «8.2» / 32768 - «33»
Built-in inductive antenna
Warranty: 1 year

Application:

Detection of cables and metal pipelines underground up to 6 m depth.
Measurement of the depth by passive “electromagnetic” method.
Tracing of underground utilities at distance up to 3 km.
Survey the ground before the ground works (BB mode).
Tracing of the buried utility without direct connection to it.

* - At the request of the customer this receiver can be supplied with the following filter settings: 50 and 100 Hz or 60 and 120 Hz.

Specifications

Receiver AP-014 Specifications

PARAMETER	ROUTE LOCATION
Frequencies of the receiver’s filter	Main filter frequency 50(60)* / 100(120)* / 512 / 1024 / 8192 / 32768 Hz
«Broadband», (frequency range)	0,05 to 8,2 KHz
Gain factor	100 dB
Visual indication	LED scale (7 values)
Sound indication	Headphones - natural, filtered and synthesized signal
Sound indication	Built-in emitter - synthesized signal
Power supply	Voltage 1,8 to 4V - alkaline batteries АА type 1,5 V (2 pcs.)
Time of continuous operation not less than	10 hours
Operation temperature	-30С…to +50С
Location precision	+\- 0,3 m
Ingress protection rating	IP54
AP-014 receiver dimensions	145 ×70 × 24 mm
Weight of the electronic unit	0,15 kg

* - At the request of the customer this receiver can be supplied with the following filter settings: 50 and 100 Hz or 60 and 120 Hz.

Transmitter AG-105 Technical specifications

The frequencies of the continuous «Co» or pulse «Pu» signal, Hz ± 0,1% - «kHz»
Load «clips» or «clamp»	512 - «0.5» / 1024 - «1.0» / 8192 - «8.2» / 32768 - «33»
«Antenna» modes	8192 - «8.2» / 32768 - «33»
Operating modes
«Antenna» modes	Internal transmitting inductor «In».
«Antenna» modes	External induction transmitting antenna «An».
«Modulation» modes (special form signal)	Pulse «Pu» (short-term transmissions of the sine signals). Transmission duration 0,12sec. Transmissions repetition frequency 1Hz.
«Modulation» modes (special form signal)	Dual-frequency «2F» (simultaneous frequency generation 1024Hz, 8192Hz). Amplitudes ratio 4/1 (respectively).
Output parameters under power supply voltage 12…15V
Output current, А
Restricted by the program under manual increment, ≥	5 – at frequency 512Hz «0.5» / 1024Hz «1.0» / 8192Hz «8.2» / «2F»
Restricted by the program under manual increment, ≥	3 - at frequency 32768Hz «33»
Set by the program for automatic adjustment with the external load of «clips» or «clamp», ≥	0,2 – at frequency 512Hz «0.5» / 1024Hz «1.0» / «2F»
	0,1 – at frequency 8192Hz «8.2» / 32768Hz «33»
Maximum output voltage, V
Depending on «modulation», ≥	32 – in the dual-frequency modulation mode «2F»
Depending on «modulation», ≥	40 – in other modes
Maximum output power, W
Restricted by the program, ≥	20 - In the continuous «Co» and pulse «Pu» modes at frequencies 512Hz «0.5» / 1024Hz «1.0» / 8192Hz «8.2» at load resistance up to 80Ω In dual-frequency mode «2F» at load resistance up to 50Ω.
Restricted by the program, ≥	6 - At frequency 32768Hz «33» at load resistance up to 260Ω.
Power supply sources
Operating range of the supply voltages	Minimally acceptable voltage for oscillation start-up - 7V.
	Maximum allowed voltage for operation – 15V.
	Automatic shutdown voltage in the “oscillation” mode < 4,2V.
Battery set	8 «alkaline» cells 1,5V «type С» Recommended – «Duracell ® ULTRA».
External power supply sources (optional)	Battery «12V» (e.g. automotive) Output voltage 11…14V, maximum current not less than 4А.
External power supply sources (optional)	Mains power supply adapter АG114М.02.020 (extra accessory based on GS60A15-P1J «MEAN WELL») Output voltage 15V, power 60W.
Operating time («life cycle»)	While in operation of the battery set «type Сх8» is defined by the quality (capacity and «load capability») of the applied alkaline cells and can be equal to from 4 to 6 hours in the «Co» и «2F» modes or from 20 to 30 hours in the «Pu» mode at initial output voltage 7W in «continuous» modes «Co» / «2F» or at initial output voltage 15W in pulse modulation mode «Pu».
Operating time («life cycle»)	Under the external power supply is fully conditioned by this external energy source characteristics therefore under mains supply operating time is unlimited.

Operational characteristics
An automatic control over the output voltage during oscillation process	Proportional control over the output power depending on the “energy potential” of the power supply source.
Automatic shutdowns of the device	At power supply voltage in the “stop” mode < 6,5V.
	At power supply voltage in the “oscillation” mode < 4,2V.
	At power supply voltage > 15,5V.
	In case of exceeding of the admissible absorbed current value (the exact figure depends on the actual mode).
	In case of short circuit of the output during the adjustment process (actuation of the hardware safety system of the terminal amplifier).
	In case of non-compliance of the oscillation mode settings depending on whether the external antenna is installed in the output or not (the switch to the “stop” mode).
	In case of “long” (≈ 100sec) downtime in the “stop” mode (if the buttons are not pushed).
Adjustment with load	Automatic, up to the reaching of the specific consumption rate or attainment of the load current: - ≥ 0,2А at frequencies 512Hz «0.5» / 1024Hz «1.0» / «2F»; - ≥ 0,1А at frequencies 8192Hz «8.2» и 32768Hz «33».
Adjustment with load	Manual after the automatic adjustment.
Connection options to the utility under examination	«Contact» connection with “earth return”.
	«Non-contact» connection with application of the internal transmitting antenna «In».
	«Non-contact» connection with the use of external induction transmitting antenna «An» (the emission intensity is higher and easier access to the utility in comparison with the internal transmitting antenna «In»).
	«Non-contact» connection using the transmitting induction “clamp” (selection of the cable from the bunch is possible).
Structural parameters
Power output amplifier	The technology — updated CLASS D Efficiency to 85%.
LED indicators	Separate light-emitting diodes indicating parameters and modes.
LED indicators	Digital indicator displaying the modes and parameters values and also showing output parameters of the «MULTIMETER» measurements, e.g.: output voltage (V), load current (А), load power (W) and load resistance (Ω /kΩ).
Overall dimensions of the electronic unit (case), not more than, mm.	216х180х105mm
The weight of the electronic unit, not more than, kg	2

The admissible environment temperatures range when in operation	- 30°С to +60°С With “battery” power supply it is not recommended to use the device under sub-zero environmental temperatures.
Ingress protection rating	IP65 (when the enclosure-case is shut).

Standard set

Standard set:

Receiver AP-014
Electromagnetic sensor EMD-247
Transmitter AG-105
Power connection cable AG120.02.080
External power supply cable AG120.02.070
Contact magnetic
Grounding rod
Receiver case
Headphones
Set carrying bag
EMD carrying bag
Operation manual
Technical passport

Accessories

Sensor DKI-117

DKI sensor is used with cable locating receiver for location of insulation damage in power cables, gas and heat pipes.

Sensor DODK-117

Searching of cable faults at shorting of its armoring to the ground. Searching of outer insulation defects of metal pipelines (water, gas) at trenchless laying.

Sensor NR-117

Selection of the cable from a bunch.

Portable electromagnetic sensor MED-127

MED-127 is used for the selection of the cable from a bunch, for location of internal wiring and cable fault location.

Clamps CI-110

Identification of the cable, the function "selection the cable from a bunch". Non-contact connection to the pipelines or to the cable. Available in various sizes.

Type C accumulators with charger

Set of type C rechargeable accumulators and chargers for AP-019 and AG-105.

AA accumulators with charger

Set of type AA rechargeable accumulators and chargers for AP-027 and AP-014.

Additional grounding accessory set

Extra grounding wire and rod for better quality of underground utility location.

220V power supply cord

Cord to power your equipment from 220V outlet.

12V power supply cord

Cord to power your equipment from vehicle accumulator.

Download

Download

Operation manual
1.27 MB

Datasheet
1.8 MB

Сertificate of Сonformity
3.6 MB

Video

Success AG-511N

Underground Cable locator AG-511N demonstration & review.

Transmitter АG-105

Portable transmitter demonstration & review.

If you want to receive price quotation for Cable and pipe locator Success AG-511N, Contact us via email: info@technoac.com or leave a message in "Contact us" section.